Shipping Delays With Covid-19 May Occur. Tell Your Clients To Plan Accordingly. Carriers Are Not Adjusting.


30 products

  • Pearl PTM Pretreatment Machine

    Pearl PTM Pretreatment Machine



  • Creek Manufacturing PREMIERE LIGHT Pretreatment (White Ink Compatible)

    Creek Manufacturing PREMIERE LIGHT Pretreatment (White Ink Compatible)

    Directions for lights are below but you can choose to use the pretreat any of these ways you'd like. Temp depends on color of the garment but lights are usually best pressed at 325F/160C and cured at the same temp or 325F/163C for 45 seconds. If you have a temperature and time that works for you then use it! Make your life simpler.  Here's what Anthony Creek recommends: 1. Hang dry then press 2 times to push fibers down 8 seconds each press.  2.  Press 2 intervals of 17 seconds each at 325F. You need to make sure that the pretreat is dry.   3. Conveyor drying: Conveyor dry at 330F for 3 minutes and 2 presses of 8 second intervals depending on how much pretreat is applied.  Usually on t shirts you will need about 19 grams of pretreat and 39 for hoodies.  We strived to create a pretreat that is/does the following: *Conveyor Friendly with heat press*Decreases Pinholes*Knocks Down Fibers Well*Can Be Hang Dried*Works With Blended Garments*Enhances White Ink Opacity*Fewer Staining Issues Than our Previous Version*Works with many DTG’s*Good Stretch*Concentrate Available for Cheaper Shipping Options*Increase in Washability*Great Price AND BEST OF ALL DOES NOT STAIN IN UV! UV results are not guaranteed, as we do not test all garments ever produced in the marketplace and we do not have control over what sealants there might be on the garments. This Pretreatment is a non-toxic spray that needs to be applied with a machine or mask. This pretreat is a great all in one solution to not have to switch pretreat! Triblends, cottons and mixed cottons will work well and print well. All Direct to Garment Printers that print white ink on dark garments require some sort of garment pretreatment. Usually the pretreatment is a spray and you spray the shirt and hit it with a heat press. This lays down all the fibers, giving you a nice, smooth garment to print. Be sure to use our Kraft paper for darks instead of parchment paper to achieve the best quality print. The pretreatment also helps ink to adhere to the garment, giving you a more vibrant final print and little or no fibrillation (small fibers sticking up out of the ink) PRETREATMENT IS A SERIOUS PRODUCT AND SHOULD PROPER MATERIALS SUCH AS GOGGLES AND MASKS SHOULD BE WORN AT ALL TIMES WHEN APPLYING. IT IS NON TOXIC BUT CAN BE TOXIC TO THE BODY IF INHALED. REMEMBER THAT PRETREATMENT IS GLUE, YOU BREATHE IN GLUE AND YOUR BODY WILL REACT TO THIS NEGATIVELY OVER TIME. 

    $24.99 - $249.99

  • Pearl Elite Pretreatment Machine

    Pearl Elite Pretreatment Machine

    The Pearl ELITE is the ultimate pretreat machine. Fabricated from premium materials, the Pearl Elite works just as good as it looks. A fully enclosed spray area and the patent pending internal filtration system guarantee zero pretreat emissions. The touch screen interface provides intuitive user control. Advanced features such as a cycle counter, level meter, production calculator and savable settings ensures consistent production. PLEASE NOTE THIS IS A MADE TO ORDER PRODUCT. AVAILABILITY DEPENDS ON PEARL, IT IS DROP SHIPPED AND PRODUCTION TIMES VARY, CONTACT US IF YOU ARE CONCERNED.


  • Pretreater IV / 4- The ultimate DTG pretreatment solution

    Pretreater IV / 4- The Ultimate DTG Pretreatment Solution

    *SALES TAX IN CA NOT INCLUDED IN PRICE PLEASE CONTACT US ABOUT AVAILABILITY AND SHIP TIMES. CANNOT RUSH. PRETREATmaker IV The high-end solution for pretreatment of DIRECT TO GARMENT PRINTING TEXTILES PRETREATmaker IV Our latest development - the PRETREATmaker IV - is an automatic high-end pretreat system for professional users resulting from consistent refinement and trend insights. As a novelty the unit is equipped with a multiphase motor (step motor). The machine does have a total of 4 valves which can be individually switched on or off. The maximum spray area is 40 cm in width and 60 cm in length. The width can be regulated by switching the 4 valves on or off. Therefore the minimal spray width is 12 cm – the ideal width for chest prints. The length can be regulated in 2 cm intervals. Spraying is possible uni- and bi-directional. This will allow each user to setup the unit according to their needs. Within the carriage we have implemented an additional filter which traps dirt from pump and tubes. This innovative filter will help to minimize blockage of the nozzles from deposition from within the system. Another novelty is the new switch-valve which allows the user to use two different precoating liquids. An additional switch is used to clean the precoating pump (incl. pipe system). For that purpose the machine offers an automatic cleaning function within the touchpad menu. All drawer rails are now equipped with an improved protection system. The PRETREATmaker IV is available with an optional scale which can be connected to the machine. After each cycle his innovation will show in the display the amount of precoating used. A useful feature to see if nozzles and system are working right. An additional feature is unlocked and will show low volume levels of precoating on the display. Another special feature of the PRETREATmaker IV is its open interface that which can be used to program the unit either directly through the client’s order system or by printing a barcode. This optional feature will simplify and speed up your workflow. With this feature the PRETREATmaker IV can be operated by untrained staff. For sure the PRETREATmaker IV is equipped with our well-known and well-proven automatic cleaning interval function. This feature prevents the nozzles from clogging during daily operation. Flushing of the nozzles with cleaner or water is limited to the last 10 cm of tube before the nozzles. This feature saves a lot of precoating liquid. Container sizes are: 1 x 10 L Precoating, 1 x 5 L Precoating, 1 x 5 L Cleaner, 1 x 5 L Waste Tank. SPECIFICATIONS Spraying area B 40 cm x L 60 cm Nozzles 4 Width Yes Lenght in 2 cm intervals Spray way uni- / bidirectional Spraying method Nozzles are moving over the table (inside) Nozzle material Brass / Stainless steel Touchpad-Display Yes Save position 5 Motor Step motor Defining application quantity Speed Carriage option (speed) 25 Pumps 2 Tanks 1x 10 L / 3x 5 L Automatic nozzle cleaning Yes Cleaning the nozzle after work (end of day) automatic Automatic pump cleaning Yes Automatic cleaning with picture in the display Yes Picture maintenance / daily handling Yes High-end filter in the carriage Yes Cleaning extern the nozzle Yes Barcode interface Yes Scale Yes Waste tank Yes Multilingual menu Yes Metric/inch Yes Ergonomic reformed drawer Yes Superuser function Yes Dimension T 90 x B 72 x H 48 cm Dimension transport T 95 x B 80 x H 61 cm Weight 70 kg Weight transport 90 kg Connection 220/230 oder 110/120 VAC Consumption 150 W Power input 2 A Main fuse 12 A Operating pressure precoating pump approx. 5,5 bar Operating pressure water pump approx. 7 bar Additional characteristics zinc- and powder-coated housing Order No. 803481 ACCESSORIES Scanner modul incl. interface 807059 Scale 807051 Tube switch for precoating pump 807049 Stainless steel spare nozzle (standard) 803427 Brass spare nozzle (standard) 803426 Brass spare nozzleextra wide hole (more suitable for Brother precoating) 803380 Stainless steel spare nozzleextra wide hole (more suitable for Brother precoating) 803463 PRETREATmaker III table 803424 PRETREATmaker III rotary table 806085 PRETREATcleaner, 1L 807068


  • Teejet TP9501EVS

    TEEJET XR 80015VS Nozzle

    TEEJET XR 80015VS Nozzle  Need help choosing the right nozzle? Check out our video


  • Teejet TP11001VS



Forgot your password?

Don't have an account yet?
Create account